# PlayStation®4 Setup

Cronus Zen™ provides compatibility for select legacy Logitech® and Fanatec® racing wheels on PlayStation®4, including support for Force Feedback, pedals, brakes, clutch, and shifter in compatible racing titles.

Wheel Mode development concluded in January 2020.\
Further expansion is not feasible due to device memory and compatibility constraints across multiple hardware brands and platforms.

For expanded racing wheel compatibility, consider Drive Hub™, a dedicated wheel adapter solution.

## Supported Racing Wheels

***

* Fanatec® ClubSport Wheel Base v1
* Fanatec® ClubSport Wheel Base v1.5
* Fanatec® ClubSport Wheel Base v2
* Fanatec® CSR
* Fanatec® CSR Elite
* Fanatec® Porsche 911 GT2
* Fanatec® Porsche 911 GT3
* Fanatec® Porsche 911 GT3 R
* Fanatec® Porsche 911 GT3 RS v2
* Fanatec® Porsche 911 Turbo
* Fanatec® Porsche 911 Turbo S
* Logitech® Driving Force GT
* Logitech® G25
* Logitech® G27

#### Fanatec® Notes

• The wheel must be set to **PS3 Mode** with the **DC power supply connected**.\
• Refer to the **Fanatec PS3 Mode** page for detailed instructions.

#### Logitech® G25 Notes

• Set the wheel to **PS3 Mode** with the **DC power supply connected**.\
• To switch between **Six-Speed** and **Sequential Mode**:

* Push down on the shift knob and rotate the **Mode Selection Dial** until the red arrow points to the desired symbol.
* In Sequential Mode, the status light is **on**.
* In Six-Speed Mode, the status light is **off**.

#### Logitech® G27 Notes

• Set the wheel to **PS3 Mode** with the **DC power supply connected**.

#### Logitech® G29 Notes

• Works directly on PS4® / PS5® without Cronus Zen™.\
• Set the wheel to **PS4 Mode** with the **DC power supply connected**.<br>

## PS4® Console Settings

***

Before setting up Wheel Mode, complete the following:

• Confirm the game supports PS4® wheel input (see compatibility list).\
• Ensure no PlayStation® controllers are paired to the console. Remove them from **Bluetooth Devices**.<br>

**Important:**\
When a DualShock®4 is connected directly to a PS4® via USB, it also pairs over Bluetooth®.\
To properly unpair a DS4 controller:

1. Connect Cronus Zen™ to the PS4® using any controller.
2. Go to **Settings → Devices → Bluetooth Devices**.
3. Select the controller and choose **Forget Device**.\
   This prevents automatic Bluetooth re-pairing.

## Required PS4® Settings

***

Navigate to:

**Settings → Devices → Controllers**\
• Select controller → Press **OPTIONS** → **Forget Device**\
• Communication Method → **Use USB Cable**

**Settings → Power Save Settings**\
• Set Time Until Controllers Turn Off → **Do Not Turn Off**

![Document image](https://images.archbee.com/IwUlH55FdaPsVELSqm1Fc/wrd9Td_LmOlcJbswS6zmV_image.png?format=webp)![Document image](https://images.archbee.com/IwUlH55FdaPsVELSqm1Fc/GF9a0xX4zPyr09y6cj7q__image.png?format=webp)![Document image](https://images.archbee.com/IwUlH55FdaPsVELSqm1Fc/sXbTOYQlH3UwrTT_j5u2u_image.png?format=webp)![Document image](https://images.archbee.com/IwUlH55FdaPsVELSqm1Fc/SGN4ZdNNc3ahylfVr9YvB_image.png?format=webp)

## Setup PS4® Wheel Mode

***

Supported racing wheels are automatically mapped to emulate a Logitech® G29 profile with Force Feedback (FFB) support.\
No manual button remapping is required.

## **IMPORTANT**

***

&#x20;If your wheel requires an external power supply (e.g., Logitech® G25, G27, G29 – DC 24V 2A / 48W), it **must** be connected.\
All peripherals supplied with the wheel (pedals, brake, clutch, shifter, etc.) must also be connected.

Operating the wheel without the required power supply may result in abnormal behavior, including:

• No Force Feedback\
• Continuous button inputs (e.g., D-Pad registering repeatedly)\
• Clutch or pedal input not detected

Example: A Logitech® G27 used without its power supply in Gran Turismo® 7 may exhibit these issues.

A licensed PS4® authentication controller must be connected to **A1** to prevent periodic disconnection (approximately every 8–10 minutes).

The DualShock®4 CUH-ZCT2 (DS4 v2) is recommended for PS4® authentication and crossover setups.

<table><thead><tr><th>DS4 Model</th><th width="101">License Donor</th><th width="116">Audio USB</th><th width="113">Audio Bluetooth</th><th width="134">DS4 Speaker</th><th>Switch Audio</th></tr></thead><tbody><tr><td>CUH-ZCT1X</td><td><mark style="color:red;"><strong>NO</strong></mark></td><td><mark style="color:red;"><strong>NO</strong></mark></td><td><mark style="color:red;"><strong>NO</strong></mark></td><td><mark style="color:red;"><strong>NO</strong></mark></td><td><mark style="color:red;"><strong>NO</strong></mark></td></tr><tr><td>CUH-ZCT2X</td><td><mark style="color:green;"><strong>YES</strong></mark></td><td><mark style="color:green;"><strong>YES</strong></mark></td><td><mark style="color:green;"><strong>YES</strong></mark></td><td><mark style="color:green;"><strong>YES</strong></mark></td><td><mark style="color:green;"><strong>YES</strong></mark></td></tr></tbody></table>

*X: U=USA, E=Europe, J=Japan*

## **RACING WHEEL (USB)**

***

#### Requirements

• PlayStation®4 console\
• DualShock®4 v2 (CUH-ZCT2) authentication controller\
• Zen Studio installed on a Windows® PC

#### Configure Wheel Mode

**1.** Connect Cronus Zen™ to a PC using the **PROG USB port**.

**2.** Open **Zen Studio → Tools → Zen Operational Mode**.\
Select **Wheel Mode**, then click **Finish**.

The **Wheel Mode logo** should appear on the Zen OLED screen.

**3.** In **Zen Studio → Device Panel**:\
• Set **Emulator Output Protocol → AUTO**\
• Ensure **PS4 Speciality** is disabled\
• Ensure **PS Remote Play** is disabled

**4.** Press the Zen **reset button** once.\
Confirm that Wheel Mode is active in the status bar.

If “Device Disconnected” appears, unplug and reconnect the **PROG USB cable**.

#### Connect Hardware

**5.** Disconnect all cables from the Zen (no power).

**6.** Connect the **DualShock®4 v2** to **A1** (authentication controller).

**7.** Connect a compatible **racing wheel** to **A3**.\
Ensure the wheel’s **external power supply** is connected.

**8.** Connect Cronus Zen™ to the PS4® using the **CONSOLE/PC USB port**.

**9.** Press the Zen **reset button** to complete synchronization.

**Important:**\
If using a **PS4 Pro**, connect the Zen to a **rear USB port** on the console.

## **Warning**

***

During Force Feedback (FFB) initialization and auto-calibration, do not touch the wheel.\
Unexpected movement may cause injury or result in incorrect calibration.

For additional methods and troubleshooting related to Fanatec® PS3 Mode, refer to the relevant topic in the Cronus forums.